2015-ös Outback külső tükör szerelése

GLASS/WINDOWS/MIRRORS > Outer Mirror Assembly

DISASSEMBLY

CAUTION:

  • When removing the mirror – repair, be careful not to damage the back surface of mirror – repair with a flat tip screwdriver.
  • When installing the mirror – repair, insert the connector and clip securely.
  1. Operate the remote control mirror switch to face the mirror – repair upward.
  2. Remove the ground terminal from the battery sensor.
  3. Remove the mirror – repair.

(1) Using a flat tip screwdriver or similar tool, release the engagement shown in the figure, and slide the mirror – repair downward to remove.

(2) Disconnect the mirror heater connector. (Model with mirror heater)

Release the claws, and then remove the cover – cap outer mirror lower.

3.

  1. 5. Release the claws, and then remove the cover – cap outer mirror.

CAUTION:

Be careful not to apply excessive force when removing the cover – cap outer mirror, as the lower hooks may become damaged.

  1. Remove the light assembly – side turn mirror. (Model with side turn signal light)(1) Remove the screws and pull out the light assembly – side turn mirror to the front of the vehicle.

    (2) Disconnect the connector and remove the light assembly – side turn mirror.

 

Assembly:

CAUTION:

Be careful not to catch the harness in between the parts.

  1. Install the light assembly – side turn mirror.
  2. Install the cover – cap outer mirror.
  3. Install the cover – cap outer mirror lower.
  4. Check that all the claws are securely engaged.

 

 

INSPECTION

  1. CHECK MOTOR OPERATION
  2. Check the mirror operation when battery voltage is applied between the connector terminals.
Terminal No. Inspection conditions Switch position
OFF
3 (+) — 8 (−) Apply battery voltage between terminals. UP
8 (+) — 3 (−) Apply battery voltage between terminals. DOWN
7 (+) — 3 (−) Apply battery voltage between terminals. LEFT
3 (+) — 7 (−) Apply battery voltage between terminals. RIGHT
  1. If it does not operate normally, replace the outer mirror assembly.
  2. CHECK OUTER MIRROR ASSEMBLY OPERATION

Check the folding operation as follows with outer mirror attached to the front door.

NOTE:

  • Because the installation angle for outer mirror assembly varies on driver’s side and passenger’s side, the outer mirror assembly on the driver’s side operates a little bit slower when operated by the folding switch.
  • Noise or unfolding operation may occur in the steps 3), 5) and 6). This is not a malfunction.
  • Since manually switching the folding or running position may cause loose fit after inspection, be sure to operate the switch electrically.
  1. Check that the left and right outer mirror assemblies with the running position are folded by pressing the folding switch.
  2. Check that the left and right outer mirror assemblies with the folding position are unfolded by pressing the folding switch.
  3. Check the folding operation on one side.

(1) Manually set the outer mirror assembly on one side from running position to folding position.

(2) Check that the outer mirror assembly on the other side is folded by pressing the folding switch.

(3) Check that loose fit condition does not exist both in running position and in folding position by operating the folding switch.

(4) Perform the inspection on left and right sides.

  1. Check the unfolding operation on one side

(1) Manually set the outer mirror assembly on one side from folding position to running position.

(2) Check that the outer mirror assembly on the other side is returned to the running position by pressing the folding switch.

(3) Check that loose fit condition does not exist both in folding position and in running position by operating the folding switch.

(4) Perform the inspection on left and right sides.

  1. Check the operation with the folding switch OFF

(1) With IG OFF, push the outer mirror assembly from running position to the front by hand.

(2) With ACC ON or IG ON, it is unfolded to the front and stops.

(3) With the outer mirror assembly unfolded to the front and stopped, turn on the folding switch, and check that the outer mirror assembly is folded.

  1. Check the operation with the folding switch ON

(1) With IG OFF, push the outer mirror assembly from running position to the front by hand.

(2) When the ignition switch is turned from IG OFF to ACC ON or IG ON, check that the outer mirror assembly starts folding from where it is pushed and goes all the way.

  1. Check operation with obstacles

(1) Set an obstacle on the mirror side of the outer mirror assembly.

(2) Operate the folding switch, and check that the outer mirror assembly with an obstacle is blocked and stopped and the other one is folded.

(3) After removing the obstacle, turn the folding switch to OFF and set the running position.

(4) When the folding switch is turned on again, check that the outer mirror assembly is set to the folding position.

(5) Perform the inspection on left and right sides.